Michigan Drill 208A Series High-Speed Steel Extra Long Drill Bit, Bright Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 1/8″ Size (Pack of 1)
- High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 1/8-inches size. Round shanks allow use with a wide variety of tool holding systems.
Michigan Drill 212M Series High-Speed Steel Extra-Long Length Drill Bit, Ground Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 8mm Size, 12″ Length (Pack of 1)
- When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Long length for extra reach ideal for deep hole drilling. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Available in ground finish. Round shanks allow use with a wide variety of toolholding systems.
Michigan Drill 208A Series High-Speed Steel Extra Long Drill Bit, Bright Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 5/32″ Size (Pack of 1)
- Round shanks allow use with a wide variety of tool holding systems. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 5/32-inches size.
Michigan Drill 212M Series High-Speed Steel Extra-Long Length Drill Bit, Ground Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 13mm Size, 12″ Length (Pack of 1)
- Available in ground finish. Long length for extra reach ideal for deep hole drilling. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems.
Michigan Drill 703C P5X Super Cobalt Steel “P” Type Cut-Off Blade, T-Shaped, 6″ Length x 1/8″ Width x 7/8″ Height
- The narrow design conserves material being cut and reduces the heat generated when cutting. Available in t-shaped style. Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys. Produces a chip narrower than the blade itself and is suited for cutting off, grooving and similar operations. Increased clearance angles on each side of the blade reduces friction.
Michigan Drill 300 Series High-Speed Steel Jobber Length Drill Bit, Black Oxide Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 33/64″ Size (Pack of 1)
- Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Creates a porous layer that holds cutting oil which provides abrasion resistance and improved chip flow.
Michigan Drill 208 Series High-Speed Steel Extra Long Drill Bit, Ground Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 21/64″ Size (Pack of 1)
- 21/64-inches size. Round shanks allow use with a wide variety of tool holding systems. 118 degrees conventional point. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
Michigan Drill 212M Series High-Speed Steel Extra-Long Length Drill Bit, Ground Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 7mm Size, 12″ Length (Pack of 1)
- Long length for extra reach ideal for deep hole drilling. Available in ground finish. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
Michigan Drill AR5 Carbide Tipped Straight Turning Tool Bit, Right Hand, 5/16″ Square Shank, 2-1/4″ Length
- 2-1/4-inches length. Ideal for c-5/c-6 steel and ferrous materials. Designed to use with right hand. Michigan drill carbide tipped straight turning tool bit for turning on the outside of the part.
Michigan Drill BH34B Precision Hardened Steel Boring Head with Integrated Straight Shank, 2-1/2″ Diameter, 5-13/16″ Length
- 001 micrometer dial. Made in usa. 3/4-inches offset travel, 3/4-inches vertical hole spacing and 2-5/8-inches shank length. Michigan drill boring head with integrated straight shank. Boring capacity up to 4-inches. Direct reading 0. Made from precision hardened steel.
Michigan Drill 212X Series High-Speed Steel Reduced Shank Drill Bit, Ground Finish, 1/2″ Round Shank, Spiral Flute, 118 Degrees Conventional Point, 5/8″ Size, 12″ Length (Pack of 1)
- 1/2-inches diameter reduced shank for 1/2-inches capacity chucks. Available in ground finish. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Round shanks allow use with a wide variety of toolholding systems.
Michigan Drill 355 Series High-Speed Steel Jobber Length Step Drill Bit, Uncoated (Bright) Finish, Round Shank, Spiral Flute, 118 Degrees Point, 8-32 Screw Size (Pack of 1)
- For screw size 8-32. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems.
Michigan Drill 208 Series High-Speed Steel Extra Long Drill Bit, Ground Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 17/64″ Size (Pack of 1)
- When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 17/64-inches size. 118 degrees conventional point. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Round shanks allow use with a wide variety of tool holding systems.
Michigan Drill 218 Series High-Speed Steel Extra-Long Length Drill Bit, Ground Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 37/64″ Size, 18″ Length (Pack of 1)
- When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. For general purpose drilling in applications where extra reach is required. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Round shanks allow use with a wide variety of toolholding systems. Available in ground finish.
Michigan Drill 203 Series High-Speed Steel General Purpose Drill Bit, #2 Morse Taper Shank, Spiral Flute, 118 Degrees Conventional Point, 1″ Size (Pack of 1)
- Morse taper shank allows the tool to be inserted directly into the machine’s spindle to facilitate high-torque applications such as large cut diameters. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 118 degrees conventional point. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 1-inches size.
Michigan Drill 212 Series High-Speed Steel Extra-Long Length Drill Bit, Ground Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 5/8″ Size, 12″ Length (Pack of 1)
- When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. Long length for extra reach ideal for deep hole drilling. Available in ground finish. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
