Coolest 23 Southeast Tools

 

Southeast Tool SDK510 Carbide-Tipped Door Knob 3 Wing Drill Bit – 2-1/8″D, 5-3/4″OAL, 1/2″Shk, Flat - Works on ruvo machinery great for masonite. 2-1/8″ plug-less bit, flat on shank. This bit features carbide at a 30 angle, the result is clean cuts, while shavings peel away. 5-3/4″ overall length.

 

Southeast Tool 129335 Carbide Tipped Lock Boring Bit – 1-7/8″ D w/ 1 Flat Shank, 5-3/4″ OAL - Works with most pre-hung door equipment. All bits have 1/2″ shank. Carbide tipped for long life, these bits are recommended for wood doors. 5-3/4″ overall length.

 

Southeast Tool SEHMA-3/8-XL Arbors For Screw-On Mortise Bits – 3/8″ D x 2-5/8″ OAL, 1/4-28 Thread - Thread size, 1/4-28. Arbor, 3/8″.

 

Full Bead Bit, 3/16 Radius, 1″ Dia, 1/2 Cut Length, 1/4 Shank, Southeast Tool SE3192 - It also acts like a suspension on a car in that it cushions the hard carbide tool tip to protect it from chipping, breaking and excess wear. Full bead, form router bits, carbide tipped, southeast tool se3192 3/16 radius, 1 cutting diameter, 1/2 cutting length, 1/4 shank. This makes it expensive but it is really worth it. This gives you the incredible long wear of carbide (up to 100 times that of steel) and the toughness of a steel saw plate, router shaft, etc. ) carbide brazing is done with a high silver braze alloy. (There are other definitions but they are all pretty close to this. Brazing is the joining of two dissimilar materials through the use of a third material at temperatures above 800° f. Unlike other attachment methods, good brazing forms a mechanical and a chemical bond between the carbide and the steel so that the bond is much stronger than either the steel or the carbide. Braze tools ( ct carbide tipped or tct tungsten carbide tipped ) have a piece of expensive tungsten carbide brazed to a steel shaft. It makes a clearly superior tool at a greatly reduced cost. The braze alloy (silver solder, high silver solder, high temp silver solder) is about 50% silver.

 

Southeast Tool SE29012 General Purpose Drill Bits – 3/16″D, 3-1/2″OAL, 2-5/16″Flute, 1-3/16″Shnk, RH - High speed steel, much longer life than carbon steel 118 point. No x10 general purpose jobbers length straight shank twist drills. Diameter, 3/16″ decimal equivalent, 1875″. Overall length, 3-1/2″ twist length, 2-5/16″.

 

Southeast Tool SDK500 Carbide-Tipped Door Knob 3 Wing Drill Bit – 2-1/8″D, 5-3/4″OAL, 1/2″Shk - The braze alloy (silver solder, high silver solder, high temp silver solder) is about 50% silver. Unlike other attachment methods, good brazing forms a mechanical and a chemical bond between the carbide and the steel so that the bond is much stronger than either the steel or the carbide. Brazing is the joining of two dissimilar materials through the use of a third material at temperatures above 800° f. It makes a clearly superior tool at a greatly reduced cost. This makes it expensive but it is really worth it. It also acts like a suspension on a car in that it cushions the hard carbide tool tip to protect it from chipping, breaking and excess wear. Door knob 3 wing drill, (drill press,boring and milling machine use only, carbide tipped, southeast tool sdk500 2 1/8 cutting diameter, 1/2 shank, 5 3/4 overall length. No flatbraze tools ( ct carbide tipped or tct tungsten carbide tipped ) have a piece of expensive tungsten carbide brazed to a steel shaft. (There are other definitions but they are all pretty close to this. This gives you the incredible long wear of carbide (up to 100 times that of steel) and the toughness of a steel saw plate, router shaft, etc. )Carbide brazing is done with a high silver braze alloy.

 

Southeast Tool 129336 Carbide Tipped Lock Boring Bit – 2-1/8″ D w/ Round Shank, 5-3/4″ OAL - Works with most pre-hung door equipment. Carbide tipped for long life, these bits are recommended for wood doors. 5-3/4″ overall length. All bits have 1/2″ shank.

 

Southeast Tool SBPT1T-L-48L Brad Point Drill Bit w/ 18″ Auger Bit – 1/2″ D x 48″ L - 48″ brad point drill. This extra-long drill bit can be used for door preparations where an extended length is required. Mounts in a 1/2″ drill motor. Cutting length 6″.

 

Southeast Tool SBPT1T-L-18L Drill Bit – 1/2″ Diameter x 18″ Long - For masterline extension flush bolt drill fixture. 18″ replacement drill bit.

 

Southeast Tool SLAT780 Carbide Tipped Latch Bore Bit – 6″ OAL x 1″ D x 1/2″ Shank, w/ Flat - Unlike other attachment methods, good brazing forms a mechanical and a chemical bond between the carbide and the steel so that the bond is much stronger than either the steel or the carbide. It also acts like a suspension on a car in that it cushions the hard carbide tool tip to protect it from chipping, breaking and excess wear. (There are other definitions but they are all pretty close to this. Brazing is the joining of two dissimilar materials through the use of a third material at temperatures above 800° f. This gives you the incredible long wear of carbide (up to 100 times that of steel) and the toughness of a steel saw plate, router shaft, etc. This makes it expensive but it is really worth it. The braze alloy (silver solder, high silver solder, high temp silver solder) is about 50% silver. With flatbraze tools ( ct carbide tipped or tct tungsten carbide tipped ) have a piece of expensive tungsten carbide brazed to a steel shaft. It makes a clearly superior tool at a greatly reduced cost. )Carbide brazing is done with a high silver braze alloy. Door latch drill bits, for automated pre-hung door equipment, carbide tipped, southeast tool slat780 1 cutting diameter, 1/2 shank, 6 overall length.

 

Southeast Tool SBPT1F Carbide-Tip Brad Point Twist Bit – 1″D x 4″Twist x 6″OAL, 1/2″ Shank w/ 3 Flat - 1″, three flats 1/2″ shank. Recommended for drive-in bolts. No 200 ct for latch bore. 5-15/16″ overall length.

 

Southeast Tool SBT1T Carbide-Tip Brad Point Twist Bit – 1″D, 4″Lgt, 5-13/16″OAL, 7/16-14″ Shk/Thread - 1″, threaded flats 1/2″ shank. No 200 ct for latch bore. Recommended for drive-in bolts. 5-15/16″ overall length.

 

Southeast Tool SDR305 3-Wing Bit – 5/8″ D x 6″ OAL x 1/2″ Shank - Overall length, 6″ twist length, 1″. Also excellent for lock hole boring in wood doors. Size, 5/8″ shank, 1/2″. Bore plastic formica and tempered masonite as well as abrasive materials and hard wood.

 

Southeast Tool SLAT790 Carbide Tipped Latch Bore Bit – 5-7/8″ OAL x 1″ D x 7/16″ Shank, Threaded - Carbide-tipped. 1″, threaded shank. 5-7/8″ length. Norfield latch boring bits.

 

Southeast Tool SDR410 3-Wing Bit – 2-1/8″ D x 6″ OAL x 1/2″ Shank - Precision ground and hand inspected only the very best materials and grinding techniques used. The most accurate er32 collet in the industry- average 00002″ total indicated runout (tir). Clamping range 398-437″. No 812-ct carbide-tipped 3-wing drill.

 

Southeast Tool 129333 Carbide Tipped Lock Boring Bit – 1-5/8″ D w/ 1 Flat Shank, 5-3/4″ OAL - 5-3/4″ overall length. Works with most pre-hung door equipment. Carbide tipped for long life, these bits are recommended for wood doors. All bits have 1/2″ shank.

 

Southeast Tool SLOC605 Carbide-Tipped Door Bit – 2-1/8″ D x 1/2″ Shank x 5-3/4″ OAL, 3 Flat on Shank - Carbide tipped for long life, these bits are recommended for wood doors. 5-3/4″ overall length. All bits have 1/2″ shank. Works with most pre-hung door equipment.

 

Face Frame Drill Bit, 3/8 Dia, Complete Assembly, Southeast Tool SFFB800 - It also acts like a suspension on a car in that it cushions the hard carbide tool tip to protect it from chipping, breaking and excess wear. This gives you the incredible long wear of carbide (up to 100 times that of steel) and the toughness of a steel saw plate, router shaft, etc. The braze alloy (silver solder, high silver solder, high temp silver solder) is about 50% silver. Brazing is the joining of two dissimilar materials through the use of a third material at temperatures above 800° f. Unlike other attachment methods, good brazing forms a mechanical and a chemical bond between the carbide and the steel so that the bond is much stronger than either the steel or the carbide. )Carbide brazing is done with a high silver braze alloy. Complete assembly for evans, ritter, unique, marcon and norfield face frame machinesbraze tools ( ct carbide tipped or tct tungsten carbide tipped ) have a piece of expensive tungsten carbide brazed to a steel shaft. It makes a clearly superior tool at a greatly reduced cost. Face frame, drill bits (complete assembly), carbide tipped, southeast tool sffb800 3/8 cutting diameter, 4 overall length. This makes it expensive but it is really worth it. (There are other definitions but they are all pretty close to this.

 

Southeast Tool 129326 Carbide Tipped Latch Bit – 15/16″D x 1/2″ Shank x 6-1/4″OAL w/Round Shank - Carbide-tipped. 6-1/4″ length. Norfield latch boring bits. 5/16″.

 

Southeast Tool SE29008 General Purpose Drill Bits – 1/8″D, 2-3/4″OAL, 1-5/8″Flute, 1-1/8″Shank, RH - High speed steel, much longer life than carbon steel 118 point. Overall length, 2-3/4″ twist length, 1-5/8″. Diameter, 1/8″ diameter, 1/8″. No x10 general purpose jobbers length straight shank twist drills.

 

Southeast Tool SDR310 3-Wing Bit – 7/8″ D x 6″ OAL x 1/2″ Shank - Bore plastic formica and tempered masonite as well as abrasive materials and hard wood. Also excellent for lock hole boring in wood doors. Overall length, 6″ twist length, 1″. Size, 7/8″ shank, 1/2″.

 

Southeast Tool SDR410F 3-Wing Bit w/ Flat – 2-1/8″ D x 6″ OAL x 1/2″ Shank w/ FLAT - Size, 2-1/8″. Shank, 1/2″. Overall length, 6″ twist length, 1″. Also excellent for lock hole boring in wood doors.

 

Southeast Tool SLOC600 Carbide-Tipped Door Bit – 2-1/8″ D x 1/2″ Shank x 5-3/4″ OAL w/Flat on Shank - With flat on shank braze tools ( ct carbide tipped or tct tungsten carbide tipped ) have a piece of expensive tungsten carbide brazed to a steel shaft. (There are other definitions but they are all pretty close to this. Brazing is the joining of two dissimilar materials through the use of a third material at temperatures above 800° f. The braze alloy (silver solder, high silver solder, high temp silver solder) is about 50% silver. This makes it expensive but it is really worth it. It also acts like a suspension on a car in that it cushions the hard carbide tool tip to protect it from chipping, breaking and excess wear. Unlike other attachment methods, good brazing forms a mechanical and a chemical bond between the carbide and the steel so that the bond is much stronger than either the steel or the carbide. Door boring bit for automated pre-hung door equipment, carbide tipped, southeast tool sloc600 2 1/8 cutting diameter, 1/2 shank, 5 3/4 overall length. This gives you the incredible long wear of carbide (up to 100 times that of steel) and the toughness of a steel saw plate, router shaft, etc. It makes a clearly superior tool at a greatly reduced cost. ) Carbide brazing is done with a high silver braze alloy.

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.