Micro Mesh 19 Piece Woodworkers Pack with 18 Abrasive 3 Inch by 6 Inch Sheets and a Foam Sanding Block
- Micro mesh performs very well in conjunction with polyurethane,polyester,epoxy,lacquer and so on follow the manufacturer’s recommended cure times prior to re-coating or applying the finish coat when you are applying multiple coats, sand from 1500 micro mesh to 3200 or 3600 between coats to remove any orange-peel or dirt after the final coat has fully cured, polish the surface beginning with 2400 micro mesh and continue through the series (3200-12000) until the desired gloss is achieved. Micro mesh is a unique cushioned abrasive that produces a very fine and uniform scratch pattern the nine grades of abrasives range from 1500 grit to 12000 grit the 1500 is similar in grit range to conventional 400 grit wet/dry sandpaper the 12000 will leave a scratch pattern that cannot be detected by the human eye and produces a wonderful looking finish micro mesh abrasives can polish to a high reflective state or leave a matte or satin finish depending upon where you stop while using the. Satin finishes are achieved by sanding up to the 3600 grade the satin finish gets progressively higher in gloss through the 6000 step high gloss finishes will appear by the 6000 through 12000 step the wood, the finish used and personal preference determine where to stop micro-gloss liquid abrasive can be hand rubbed onto the finish following the 12000 micro meshstep for an “ultra” high gloss finish. Before starting the micro mesh cycle of abrasive sanding, coarse sanding should be done using up to 320 grit sandpaper shaping, sawing or turning of the work piece should be completebegin with 1500 micro mesh sand until all of the sandpaper scratches are removed continue with the micro-mesh series and cycle up to the desired look (1800, 2400, 3200, 3600, 4000, 6000, 8000, 12000) thinned lemon oil or danish oil can be applied as a finish on bare wood. 🇺🇸 this made in the usa kit contains 2 each of the following 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 and 12000 micro mesh can be used wet or dry when using micro mesh dry, it can be “unloaded” by rapping against the palm of your hand micro mesh can also be cleaned by using a stiff, short bristled brush it may not be necessary to go through every grade of micro mesh to reach the desired finish.
Norton T414 Blue-Bak Abrasive Sheet, Paper Backing, Silicon Carbide, Waterproof, Grit 500 (Pack of 10)
- Silicon carbide is more aggressive and cuts faster than aluminum oxide. Waterproof for use in wet or dry applications. Closed coat for a higher-quality finish than an open-coat sheet. Full resin bonding system for increased strength and durability. Paper backing is flexible, and offers a more consistent finish than cloth or fiber.
3M Imperial Wet or Dry 220 Grit SandPaper / Abrasive Sheets 9″ x 11″ Pkg of 5
- This great imperial abrasive sheet is made by 3m is essential for any jeweler or watchmaker. The sheet has a special resin-over-resin bonding technique that resists heat and holds the abrasive particles better, which together will give you a more uniform cut. This amazing abrasive sheet can be used, wet or dry, to provide you with a faster cut, longer abrasive life, and a more consistent finish which reduces sanding and buffing time.
WALLER PAA 1 Roll=60sheets 3M 07521 Scotch-Brite Multi-Flex Abrasive Sheet 4″ x 8″
- Replaces steel wool to eliminate contamination. Available in very fine, ultra fine & finest grades. 8″ x 20′ rolls 60 sheets per roll very fine = 320-400 grit. Convenient dispenser saves time and eliminates waste. Ultra flexible and conformable for cleaning or fine finishing.
10 Pack 3M Green Wet or Dry Tri-M-ITE Polishing Papers 30 Micron 400 Grit Jewelry Making Abrasive Sheets
- They can be used either wet or dry. Micron 30 (approximate grit size 400). Measures 8-1/2″ x 11″. They are ideal for interior shapes, and for polishing just about any contoured surface of your materials. They allow the user to remove a controlled amount of material, therefore leaving a more consistent finish.
3M Wetordry Abrasive Sheet 213Q, 02035, P800, 9 in x 11 in, 50 sheets per carton
- Comes with paper abrasive backing and aluminum oxide abrasive mineral type. Available in black color and it is converted form sheet. Most flexible backing with more consistent scratch pattern. Used in wet sanding, fine featheredging or last final sanding step before priming. Imperial wet or dry sheet.
Norton ProSand Premium Job Pack Abrasive Sheet, Next Generation of 3X Technology, Fiber Backing, Aluminum Oxide, Grit P120 (Pack of 20)
- For light stock removal and surface leveling. Reduces sanding time. Load resistant stearate coating, fiber reinforced backing, and high quality zirconia alumina combine to give 3x the performance of typical aluminum oxide paper sheets. Zirconia alumina is self-sharpening and durable, allowing for a faster cut rate than aluminum oxide. Water-based stearate coating resists loading for extended abrasive life. The first choice for any sanding project. Will not clog, tear or transfer color. Open-coat construction offers more flexibility and clog resistance than a closed-coat sheet. Paper backing is flexible, and offers a more consistent finish than a cloth or fiber backing, while being thicker and more durable than a polyester film backing. Works on all surfaces.
Norton Multisand Job Pack Abrasive Sheet, Paper Backing, Aluminum Oxide, Grit P180 (Pack of 25)
- Open-coat construction offers more flexibility and clog resistance than a closed-coat sheet. P-graded aluminum oxide is tough and offers a very consistent scratch pattern for a high-quality finish. For hand or machine sanding a wide variety of materials, from plastics to metals. Aluminum oxide is durable and the most common abrasive grain. Paper backing is flexible, and offers a more consistent finish than cloth or fiber.
KUDOS.JP Sandpaper for Plastic Models, Automotive Sanding, Wood Furniture Finishing, Before Paint Finishing 60 to 1000 Grit Assortment Abrasive Paper 6 Sheets (Japan Import)
- 6 sheets sandpaper 60 to 1000. Fine grid (for finish polishing of wood etc) 320 to 400. Rough grid (for rough grinding etc) 60 to 120. Middle grid (for rough finishing before painting etc) 150 to 240. Fine grid (for finish polishing before painting etc) 600 to 1000.
3M Wetordry Abrasive Sheet 413Q, 02004, 320, 9 in x 11 in, 50 sheets per carton
- Resin bonding resists deterioration from heat, extending the life of the abrasive cloth. Used wet or dry. Light, aweight paper backing offers excellent flexibility in handson applications. Silicon carbide mineral provides an aggressive cut and a consistent, fine finish. Can be easily cut and folded to fit any hand tool or work piece crevice. Waterproof material allows for easy debris removal. Great finishing.
Norton T414 Blue-Bak Abrasive Sheet, Paper Backing, Silicon Carbide, Waterproof, Grit 240 (Pack of 50)
- Full resin bonding system for increased strength and durability. Closed coat for a higher-quality finish than an open-coat sheet. Silicon carbide is more aggressive and cuts faster than aluminum oxide. Paper backing is flexible, and offers a more consistent finish than cloth or fiber. Waterproof for use in wet or dry applications.
Norton T401 Black Ice Abrasive Sheet, Paper Backing, Silicon Carbide, Waterproof, Grit 1200 (Pack of 50)
- Closed coat for a higher-quality finish than an open-coat sheet. Paper backing is flexible, and offers a more consistent finish than cloth or fiber. Silicon carbide is more aggressive and cuts faster than aluminum oxide. Waterproof sheet for use in wet or dry applications. Full resin bonding system for increased strength and durability.
3M Company 3M-7521 Scotch-Brite Multi-Flex Abrasive Sheet Roll
- Size, 4 w x 8 l in. Convenient dispenser saves time and eliminates waste. Color, maroon. Ultra flexible and conformable for cleaning or fine finishing. Product form, sheet roll. Features. Attachment method, none. Sanding method, hand machine. Replaces steel wool to eliminate contamination. Sanding surface, paint primer.
10 Pack 3M Light Green Wet or Dry Tri-M-ITE Polishing Papers 1 Micron 8000 Grit Jewelry Making Abrasive Sheets
- They are ideal for interior shapes, and for polishing just about any contoured surface of your materials. They allow the user to remove a controlled amount of material, therefore leaving a more consistent finish. Micron 1 (approximate grit size 8000). Measures 8-1/2″ x 11″. They can be used either wet or dry.
3M Red Abrasive Stikit Sheet Roll, 01687, P120, 2-3/4 in x 25 yd
- Highvalue reattachable abrasive ideal for featheredging and primer sanding. A or dweight paper backing ensure best results for specific projects. Aluminum oxide abrasive offers a fast cut, long disc life and professional results. Roll may be cut and shaped to meet project needs and dimensions. Stikit attachment makes for fast, efficient tool attachment.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
