Niagara Cutter N45061 High Speed Steel Square Nose End Mill, Weldon Shank, Uncoated, Roughing/Finishing Cut, Non-Center, 30-Degree, 4-Flute, 3.25″ OAL, 0.188″ Cut Diameter, 0.375″ Shank Diameter
- Square nose end mills (also called square end) create sharp, unrounded cuts. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. High-speed steel is compatible with a variety of materials. Double-end end mills have cutting edges on both ends for longer tool life. Four flutes produce a better finish than fewer flutes.
Precision Twist E6302 Carbide Square Nose End Mill, Long Reach, Uncoated (Bright) Finish, Roughing Cut, 30 Deg Helix, 2 Flutes, 3″ Overall Length, 3/16″ Cutting Diameter, 3/16″ Shank Diameter
- Square nose end mills (also called square end) create sharp, unrounded cuts. Extra-long length end mills have longer cutting edges and can make deeper cuts than long-length end mills. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.
CGC Tools CEM14F3 Primate Square Nose End Mill, 3 Flute, 1/4″ Diameter, 3/4″ LOC, 2-1/2″ OAL
- Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Extremely versatile in various materials, center cutting, solid sub-micron carbide. Usa, flat, 3 flute, 1/4” diameter, 3/4” length of cut, 2-1/2” overall length. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish. This weapon of mass production destroy any competition.
Niagara Cutter N44125 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated Finish, Roughing/Finishing Cut, Non-Center, 30-Degree, 4-Flute, 3.25″ OAL, 0.375″ Cut Diameter, 0.375″ Shank Diameter
- Truncated rougher-finisher removes material in less time than conventional end mills while producing a finer finish than fine- or coarse-pitch roughers. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Square nose end mills (also called square end) create sharp, unrounded cuts. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Number of flutes varies by diameter for optimum feed and cut rate.
Melin Tool CCMGS Carbide Micro Square Nose End Mill, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 1.5000″ Overall Length, 0.0750″ Cutting Diameter, 0.125″ Shank Diameter
- Round shanks allow use with a wide variety of toolholding systems. Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems. 30 degrees helix angle. 4 flutes single end. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
Niagara Cutter N40182 High Speed Steel Square Nose End Mill, Weldon Shank, Uncoated Bright Finish, Roughing/Finishing Cut, 30-Degree, 4-Flute, 3.375″ OAL, 0.563″ Cut Diameter, 0.500″ Shank Diameter
- Number of flutes varies fewer flutes have more chip-carrying capacity and more flutes produce a finer finish. High-speed steel is compatible with a variety of materials. Square nose end mills (also called square end) create sharp, unrounded cuts. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials.
Ultra Tool 32016TA Carbide Square Nose End Mill, Inch, TiAlN Finish, 30 Degree Helix, 4 Flutes, 1.5000″ Overall Length, 0.2500″ Cutting Diameter, 0.2500″ Shank Diameter
- Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems. Titanium aluminum nitride coatings become self-lubricating when used at very high speeds, making them ideal for cutting without coolant (“dry machining”). Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Cutting diameter +0000/-0002 shank diameter +00000/-00003.
Niagara Cutter N30160 High Speed Steel (HSS) Square Nose End Mill, Inch, TiN Finish, Finishing Cut, 30 Degree Helix, 3 Flutes, 4″ Overall Length, 0.500″ Cutting Diameter, 0.500″ Shank Diameter
- Titanium nitride (tin) is a general-purpose coating that combines high-temperature resistance and increased hardness compared to uncoated end mills. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Square nose end mills (also called square end) create sharp, unrounded cuts. High-speed steel is compatible with a variety of materials. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
YG-1 E1072 High Speed Steel (HSS) Square Nose End Mill, Extra Long Reach, Weldon Shank, Uncoated (Bright) Finish, 42 Deg Helix, 2 Flutes, 3.5625″ Overall Length, 0.25″ Cutting Diameter, 0.375″ Shank Diameter
- High-speed steel for general-purpose cutting. Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills. 42-degree helix provides increased cutting action compared to end mills with lower helix angles. Suitable for machining on aluminum and other nonferrous materials.
Wokesi 2 3 4 5 6 8mm Blade Diameter,Square Nose End Mill Set,Pack of 6,4Flutes,HRC55,TiAlN Coated,Tungsten Steel Carbide,CNC Router Bits Cutting Milling Tools(2/3/4/5/6/8mm HRC55)
- 3suitable for process copply,alloy,iron and steel under hrc55(hra78). 2materialtungsten carbide,high quality tialn coating,getting long tool life. 1contains 6pcs square endmills2mm/3mm/4mm/5mm/6mm8mm cutting diameter. 4high micro hardness,high abrasion resistance,good toughnesscan be high-speed processing. 5package1 pack of 6 pieces endmills.
Niagara Cutter N41672 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing and Finishing Cutting, 30-Degree, 4-Flute, 2.5″ OAL, 0.375″ Cut Diameter, 0.375″ Shank Diameter
- Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Truncated rougher-finisher removes material in less time than conventional end mills while producing a finer finish than fine- or coarse-pitch roughers. Number of flutes varies by diameter for optimum feed and cut rate.
CGC Tools GMA14F3 Gorilla Silverback Carbide Square Nose End Mill for Aluminum, Flat End, 3 Flute, 1/4″ Diameter, 3/4″ LOC, 2-1/2″ OAL
- Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Usa, silverback, flat, 3 flute, 1/4″ diameter, 3/4″ length of cut, 2-1/2″ overall length. Engineered to repel aluminum for roughing and finishing of non-ferrous materials, high velocity, high material removal rate. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish.
Wokesi 1mm 1.5mm 2mm 3mm Cutter Dia,Pack of 4,Std Length,4Flutes,HRC55,TiAlN Coated,Metric,Solid Carbide,Square Nose End Mill,CNC Router Bits Cutting Milling Tools (1mm+1.5mm+2mm+3mm HRC55)
- 5package 1 pack of 4 pieces endmill cutter. 1contains 4pcs square endmills1pc×1mmdia,1pc×15mmdia,1pc×2mmdia and 1pc×3mmdia. 4high micro hardness,high abrasion resistance,good toughness. 3suitable for process alloy,iron and steel under hrc55high performance. 2materialtungsten carbide,high quality tialn coating,getting long tool life.
CGC Tools CEM316F3TICN Primate Square Nose End Mill, TiCN Coating, 3 Flute, 3/16″ Diameter, 5/8″ LOC, 2″ OAL
- This weapon of mass production destroy any competition. Extremely versatile in various materials, center cutting, solid sub-micron carbide. Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish.
DIAOSnx 1/8″ 5/32” 3/16″ 1/4″ 5/16″ 3/8″ 1/2″ High Speed Steel HSS 4 Flute Straight Shank Square Nose End Mill Cutter CNC Router Bits Cutting Milling Tools (Set of 7)
- Package includes 7×end mill cutter hss-al, 4 flute, straight shank, square nose. Suitable for cnc data processing center, carved, high-speed machines can milling of copper, aluminum, tool steel, cast iron, etc square nose endmills size 1/8” cutter blade diameter=1/8”, shank diameter=1/4”, flute length=7/16”, overall length=2-3/8” 5/32” cutter blade diameter=5/32”, shank diameter=1/4, flute length=1/2”, overall length=2-1/4” 3/16” cutter blade diameter=3/16”, shank diameter=1/4”, flute length=9/16”, overall length=2-1/4” 1/4” cutter blade diameter=1/4”, shank diameter=1/4”, flute length=3/4”, overall length=2-1/3” 5/16” cutter blade diameter=5/16”, shank diameter=5/16””, flute length=7/8”, overall length=2-4/9” 3/8” cutter blade diameter=3/8”, shank diameter=3/8”, flute length=1”, overall length=2-3/4” 1/2” cutter blade diameter=1/2”, shank diameter=1/2”, flute length=1-1/2”,overall length=3-3/8”. Note due to the different measurement methods, the size may have 1-2cm error.
YG-1 E5065 Carbide Square Nose End Mill, Extra Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 6″ Overall Length, 0.25″ Cutting Diameter, 0.25″ Shank Diameter
- Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Four flutes produce a better finish than fewer flutes. Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Suitable for general-purpose machining on hardened and high-alloy steel, steel casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic.
Niagara Cutter N85030 High Speed Steel Square Nose End Mill, Weldon Shank, Uncoated, Roughing/Finishing Cutting, Non-Center, 30-Degree, 4-Flute, 2.3125″ OAL, 3 mm Cut Diameter, 0.375″ Shank Diameter
- Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Four flutes produce a better finish than fewer flutes. Square nose end mills (also called square end) create sharp, unrounded cuts. High-speed steel is compatible with a variety of materials. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
Niagara Cutter N61647 Carbide Square Nose End Mill, Inch, TiCN Finish, Roughing and Finishing Cut, 45 Degree Helix, 3 Flutes, 4″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter
- Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers the abrasion resistance required to machine aluminum and other nonferrous materials. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. 45-degree helix provides the efficient cutting action and chip evacuation required to machine aluminum and other nonferrous materials. Square nose end mills (also called square end) create sharp, unrounded cuts.
Niagara Cutter N85440 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 2 Flutes, 2″ Overall Length, 0.250″ Cutting Diameter, 0.250″ Shank Diameter
- Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cuttings speeds, offering better heat resistance than tin and ticn coatings. Square nose end mills (also called square end) create sharp, unrounded cuts. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
Niagara Cutter N75683 Cobalt Steel Square Nose End Mill, Weldon Shank, TiAlN Finish, Roughing Cutting, Non-Center, 30-Degree Helix, 4-Flute, 4.75″ OAL, 0.750″ Cut Diameter, 0.750″ Shank Diameter
- Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Number of flutes varies by diameter for optimum feed and cut rate. Fine-pitch tooth design is suitable for machining high-temperature alloys. Square end creates sharp, unrounded cuts and has a corner chamfer to strengthen the cutting edges. Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills.
Niagara Cutter N46420 Carbide Square Nose End Mill, Metric, AlTiN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 39mm Overall Length, 3mm Cutting Diameter, 3.000mm Shank Diameter
- Square nose end mills (also called square end) create sharp, unrounded cuts. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Four flutes produce a better finish than fewer flutes. Aluminum titanium nitride (altin) coating lubricates the end mill for high-temperature stability and abrasion resistance, offering better heat resistance than tin, tialn, and ticn coatings.
YG-1 E5065 Carbide Square Nose End Mill, Extra Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 4″ Overall Length, 0.25″ Cutting Diameter, 0.25″ Shank Diameter
- Four flutes produce a better finish than fewer flutes. Suitable for general-purpose machining on hardened and high-alloy steel, steel casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
