Stanley Proto JUSN338 12 Point Slugging Wrench 2-3/8″
- Heavy box walls provide greater transmission of torque to fastener. High strength rectangular design withstands heavy sledging. Non-reflective black oxide finish for use where non-plated products are required. Fits most 4, 6 and 12 point fasteners. 43 point box end allows for fine indexing, helping improve speed and access.
4-1/4″ Proto 12 Point Slugging Wrench USA
- It is made to be hit with a sledge hammer to loosen stubborn nuts and bolts. 6-1/8″ diameter by 2-3/4″ height on socket. It is marked usn-368 and has 12 points and is super heavy duty. The tape measure is for size comparison only, it is not included 18-1/2″ overall length. This tool is great for off road equipment repairs, industrial die maintenance and any piece of equipment needing this size limited supply. We are offering this brand new, 4 1/4″ proto box end slugging wrench. This is used for heavy industrial use. If you need this size wrench then you are in for a great deal, this retails for over $350, so don’t miss out on this one. Slugging pad is 3-1/2″ x 3″ x 1-1/2″ thick with rounded edges for safety.
Slugging Wrench, Offset, 65mm, 14-1/2 L
- This listing is for each. Technical specification item slugging wrench handle type offset sae or metric metric number of points 12 nominal size 65mm tether capable standard tool (accessory needed for tethering) overall length 14-1/2 offset 1-1/2 head thickness 41mm finish black oxide standards federal specification ggg-w-636e. Antislip design (asd) features a locking groove to prevent slippage.
6 Pt Straight Pattern Slugging Wrench 2-3/8 Inch
- 406″armstrong industrial tools 33-576 6 point straight pattern slugging wrench 2-3/8″. Of points 6opening 2-3/8″weight 6. 0 lb overall length 12-3/8″head diameter 3. Featureshardened for extra strengthwithstands stress under impactprevents rounding of fasteners’ corners”lobular” design exerts force on flats of fastenerschamfered opening slips easily over fasteners and holds securelyspecificationsno. S. Military. Armstrong brand wrenches feature precise geometry for an exacting fit and are designed to withstand the toughest conditions from factory floors to the u.
Stanley Proto JHD050M 12 Point Slugging Wrench 50mm
- Non-reflective black oxide finish for use where non-plated products are required. High strength rectangular design withstands heavy sledging. 16 point box end allows for fine indexing, helping improve speed and access. Fits most 4, 6 and 12 point fasteners. Heavy box walls provide greater transmission of torque to fastener.
Slugging Wrench, Offset, 2-21/32, 14-1/2 L
- Technical specification item slugging wrench handle type offset sae or metric sae number of points 12 nominal size 2-21/32 tether capable standard tool (accessory needed for tethering) overall length 14-1/2 offset 1-1/2 head thickness 1-5/8 finish black oxide standards federal specification ggg-w-636e. • Designed for heavy use in close quarters where hammer or sledge is required to loosen frozen nuts or set large fasteners. • Straighter handle design than striking wrenches resists springing, nut turns easier. • Non-reflective black oxide finish for use where non-plated products are required. • Heavy box walls provide greater transmission of torque to fastener. • High strength rectangular design withstands heavy sledging transmits power more effectively to fastener. • 12 point box end allows for fine indexing, helping improve speed and access. • Box opening designed to remain in place on fastener when wrench is struck. This listing is for each.
Stanley Proto JHD036M 12 Point Slugging Wrench 36mm
- Heavy box walls provide greater transmission of torque to fastener. 13 point box end allows for fine indexing, helping improve speed and access. High strength rectangular design withstands heavy sledging. Fits most 4, 6 and 12 point fasteners. Non-reflective black oxide finish for use where non-plated products are required.
Slugging Wrench, Offset, 3 in., 15-3/4 L
- This listing is for each. Technical specification item slugging wrench handle type offset sae or metric sae number of points 12 nominal size 3 tether capable standard tool (accessory needed for tethering) overall length 15-3/4 offset 1-3/4 head thickness 1-7/8 finish black oxide standards federal specification ggg-w-636e. Use to tighten collars, locknut wings, and seal-packing nuts.
6 Pt Straight Pattern Slugging Wrench 1-1/16 Inch
- 1 1/16-inch. Special heat treating provides maximum durability for long life. Anvil is proportional to opening size. Offset handle is close to the head to provide clearance in confined areas. Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners.
Stanley Proto JUSN329 12 Point Slugging Wrench 1-13/16″
- High strength rectangular design withstands heavy sledging. Non-reflective black oxide finish for use where non-plated products are required. 36 point box end allows for fine indexing, helping improve speed and access. Fits most 4, 6 and 12 point fasteners. Heavy box walls provide greater transmission of torque to fastener.
Stanley Proto JUSN324 12 Point Slugging Wrench 1-1/2″
- High strength rectangular design withstands heavy sledging. Fits most 4, 6 and 12 point fasteners. 32 point box end allows for fine indexing, helping improve speed and access. Heavy box walls provide greater transmission of torque to fastener. Non-reflective black oxide finish for use where non-plated products are required.
12 Pt 45 Degree Offset Slugging Wrench 2 Inch
- Armstrong brand wrenches feature precise geometry for an exacting fit and are designed to withstand the toughest conditions from factory floors to the u. 500″handle length 3. 875″head diameter 3. 687″ armstrong industrial tools 33-064 12 point 45 degree offset slugging wrench 2″. 72 lb overall length 13. Military. Of points 12opening 2″weight 5. Featureshardened for extra strengthwithstands stress under impactprevents rounding of fasteners’ corners”lobular” design exerts force on flats of fastenerschamfered opening slips easily over fasteners and holds securelyspecificationsno. 250″offset height 1. S. 125″handle width 1. 250″ head thickness 1. 937″handle height 1.
Slugging Wrench, Offset, 2-17/64 in., 11 L
- Straighter handle design resists springing and nut turns. Nonreflective black oxide finish. This listing is for each. High-strength rectangular design withstands heavy sledging and transmits power more effectively to fastener. The proto® slugging wrench is designed for heaving use in close quarters where a hammer or sledge is necessary to loosen frozen nuts or set large fasteners. Technical specification item slugging wrench handle type offset sae or metric sae number of points 12 nominal size 2-1/4 tether capable standard tool (accessory needed for tethering) overall length 11 offset 1-1/4 head thickness 1-3/8 finish black oxide standards federal specification ggg-w-636e. The heavy box walls provide greater torque transmission. 12-point box end opening is designed to remain on fastener when wrench is struck.
Stanley Proto JUSN342 12 Point Slugging Wrench 2-5/8″
- 47 point box end allows for fine indexing, helping improve speed and access. High strength rectangular design withstands heavy sledging. Fits most 4, 6 and 12 point fasteners. Heavy box walls provide greater transmission of torque to fastener. Non-reflective black oxide finish for use where non-plated products are required.
Stanley Proto JUSN354 12 Point Slugging Wrench 3-3/8″
- Fits most 4, 6 and 12 point fasteners. High strength rectangular design withstands heavy sledging. Heavy box walls provide greater transmission of torque to fastener. 53 point box end allows for fine indexing, helping improve speed and access. Non-reflective black oxide finish for use where non-plated products are required.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
