(Imperial Units, not Metric)1/16” 1/8” 5/32” 3/16” 1/4” 5/16” 3/8” 1/2” HSS 4 Flute Straight Shank Square Nose End Mill Cutter (8 Pcs)
- Package includes 8 x end mill cutter., Material hss, 4 flute, straight shank, square nose, suitable for aluminium, cast iron, copper, magnesium alioy, plastics, wood etc square nose endmills size 1/16” cutter blade diameter=1/16”, shank diameter=1/4”, flute length=9/16”, overall length=2-3/8” 5/32” cutter blade diameter=5/32”, shank diameter=1/4, flute length=1/2”, overall length=2-3/8” 1/8” cutter blade diameter=1/8”, shank diameter=1/4”, flute length=7/16”, overall length=2-3/8” 3/16” cutter blade diameter=3/16”, shank diameter=1/4”, flute length=9/16”, overall length=2-3/8” 1/4” cutter blade diameter=1/4”, shank diameter=1/4”, flute length=3/4”, overall length=2-1/2” 5/16” cutter blade diameter=5/16”, shank diameter=5/16””, flute length=7/8”, overall length=2-5/8” 3/8” cutter blade diameter=3/8”, shank diameter=3/8”, flute length=1”, overall length=2-3/4” 1/2” cutter blade diameter=1/2”, shank diameter=1/2”, flute length=1-1/2”,overall length=3-3/8”. Note due to the different measurement methods, the size may have 1-2cm error.
YG-1 E5020 Carbide Square Nose End Mill, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 2.5″ Overall Length, 0.25″ Cutting Diameter, 0.25″ Shank Diameter
- Center-cutting design allows the end mill to plunge into material like a drill bit for applications such as slotting, drilling, and pocketing, as well as general-purpose machining. Suitable for machining on hardened and high-alloy steel, chromium-nickel steel, steel casting, malleable cast iron, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.
Wokesi 2 3 4 6 8 10mm Blade Diameter,Square Nose End Mill Set,Pack of 6,4Flutes,HRC55,TiAlN Coated,Solid Tungsten Carbide,CNC Router Bits Cutting Milling Tools(2/3/4/6/8/10mm HRC55)
- 4high micro hardness,high abrasion resistance,good toughness. 5package1 pack of 6 pieces endmills. 1contains 6pcs square endmills2mm/3mm/4mm/6mm/8mm/10mm cutting diameter. 2materialtungsten carbide,high quality tialn coating,getting long tool life. 3suitable for process copply,alloy,iron and steel under hrc55(hra78)high performancemiddle-low speed.
YG-1 E5023 Carbide Square Nose End Mill, Double End, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 3″ Overall Length, 0.5″ Cutting Diameter, 0.5″ Shank Diameter
- Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than uncoated finish, tin coating, and ticn coating. Stub length increases the strength of the tool, making it less likely to break in the workpiece. Double-end square end mills create sharp, unrounded cuts and have cutting edges on both ends for longer tool life. Suitable for general-purpose machining on steel, chromium-nickel steel, and malleable cast iron. Four flutes produce a better finish than fewer flutes.
Wokesi Pack of 6Pcs,1/4 3/8 5/16 5/8 1/2 3/4 Blade Diameter,High Speed Steel,Extra Long,Square Nose End Mill Cutter CNC Router Bits (1/4+3/8+5/16+5/8+1/2+3/4 Extra Long 4Flute)
- 4 flute,full grinded,high abrasion resistance,obtain accuracy and fine finish. Materialm2ai,high speed steel,long tool life. Package6pc×end mill ball nose cutter. Contains 6pcs square nose long endmills1/4+3/8+5/16+5/8+1/2+3/4 blade diameter. Suitable for aluminium,cast iron,copper,magnesium alioy,plastics,wood etc.
Niagara Cutter N86022 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 3 Flutes, 2.75″ Overall Length, 0.438″ Cutting Diameter, 0.438″ Shank Diameter
- Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Square nose end mills (also called square end) create sharp, unrounded cuts.
CGC Tools CEM132F2 Primate Square Nose End Mill, 2 Flute, 1/32″ Diameter, 5/64″ LOC, 1-1/2″ OAL, 1/8″ Shank
- Usa, flat, 2 flute, 1/32” diameter, 5/64” length of cut, 1-1/2” overall length, 1/8”shank. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish. This weapon of mass production destroy any competition. Extremely versatile in various materials, center cutting, solid sub-micron carbide. Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable.
Niagara Cutter N85863 Carbide Square Nose End Mill, Weldon Shank, TiAlN Finish, Roughing and Finishing Cutting, 30-Degree Helix, 4-Flute, 2″ Overall Length, 0.188″ Cut Diameter, 0.188″ Shank Diameter
- Four flutes produce a better finish than fewer flutes. Square nose end mills (also called square end) create sharp, unrounded cuts. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Nc tolerance end mills have a plus-tolerance cutting diameter to match those of high-speed steel end mills, allowing an upgrade from high-speed steel to carbide without changing diameter.
YG-1 E5977 Carbide Square Nose End Mill, Extra Long Reach, Uncoated (Bright) Finish, Finishing Cut, Non-Center Cutting, 37 Deg Helix, 3 Flutes, 6″ Overall Length, 0.5″ Cutting Diameter, 0.5″ Shank Diameter
- 37-degree helix angle provides increased cutting action and chip evacuation compared to the standard 30-degree helix. Suitable for high-performance machining on aluminum and other nonferrous materials. Extended-reach neck style provides access to recessed areas of the workpiece. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications.
YG-1 E5058 Carbide Square Nose End Mill, TIALN Multilayer Finish, 40 Deg Helix, 6 Flutes, 3″ Overall Length, 0.5″ Cutting Diameter, 0.5″ Shank Diameter
- 40-degree helix provides increased cutting action compared to end mills with lower helix angles. Suitable for finishing on a range of materials. Six flutes produce a better finish than fewer flutes. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than uncoated finish, tin coating, and ticn coating.
Square Nose End Mill Bit Sets, 4 Flute High Speed Steel HHS Straight Shank CNC Router Bits Corner Edged Milling Cutter For Aluminum, Wood, Acrylic, PVC, etc, 2mm(2/25″)~12mm(25/12″) Set of 10
- Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys. 30 degree helix angle. Used for general purpose milling in most materials of medium and tough alloy materials such as stainless steel, nickel base alloy, brass, iron, etc. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Weldon shanks feature a round shank with one of more flats machined into the side for easy indexing and alignment.
CGC Tools CEM14F3TIALN Primate Square Nose End Mill, TiAlN Coating, 3 Flute, 1/4″ Diameter, 3/4″ LOC, 2-1/2″ OAL
- Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish. Extremely versatile in various materials, center cutting, solid sub-micron carbide. Usa, flat, 3 flute, 1/4” diameter, 3/4” length of cut, 2-1/2” overall length, tialn coating. This weapon of mass production destroy any competition.
SpeTool 12201 2 Flutes 1/4 inch Shank Square Nose End Mill Carbide CNC Upcut Router Bits Tiain Coated, 2 1/2 inches Leng
- The route bit suit for cnc router and makita, bosch, and any brand plunge router with 1/4″ collet. End mill bits are suitable for side milling, end milling, finish machining, etc. Solid carbide spiral router bit with 1/4 inch shank and 1/4 inch cutting diameter, 3/4 inch cutting length, 2-1/2 inch for total length. Flat top with 2-flute, material hrc55 carbide with tialn coated. For cnc,engraving machinecarbon steel, mould steel, inconel, stainless steel, titanium alloy etc.
Niagara Cutter N85516 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 2.5″ Overall Length, 0.219″ Cutting Diameter, 0.250″ Shank Diameter
- Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Square nose end mills (also called square end) create sharp, unrounded cuts. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Four flutes produce a better finish than fewer flutes. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials.
Niagara Cutter N61635 Carbide Square Nose End Mill, Inch, TiCN Finish, Roughing and Finishing Cut, 45 Degree Helix, 3 Flutes, 2.5″ Overall Length, 0.250″ Cutting Diameter, 0.250″ Shank Diameter
- Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers the abrasion resistance required to machine aluminum and other nonferrous materials. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Square nose end mills (also called square end) create sharp, unrounded cuts. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. 45-degree helix provides the efficient cutting action and chip evacuation required to machine aluminum and other nonferrous materials.
CGC Tools CEM14F2TIALN Primate Square Nose End Mill, TiAlN Coating, 2 Flute, 1/4″ Diameter, 3/4″ LOC, 2-1/2″ OAL
- Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish. This weapon of mass production destroy any competition. Usa, flat, 2 flute, 1/4” diameter, 3/4” length of cut, 2-1/2” overall length, tialn coating. Extremely versatile in various materials, center cutting, solid sub-micron carbide.
Niagara Cutter N52206 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, Uncoated (Bright) Finish, Finishing Cut, 30 Degree Helix, 4 Flutes, 3.625″ Overall Length, 0.750″ Cutting Diameter, 0.500″ Shank Diameter
- Square nose end mills (also called square end) create sharp, unrounded cuts. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Number of flutes varies fewer flutes have more chip-carrying capacity and more flutes produce a finer finish.
Melin Tool ERP Cobalt Steel Square Nose End Mill, Uncoated (Bright) Finish, Roughing Cut, 35 Deg Helix, 3 Flutes, 3.7500″ Overall Length, 0.6250″ Cutting Diameter, 0.625″ Shank Diameter
- A rough finish is produced which will require a finishing pass. Weldon shanks feature a round shank with one of more flats machined into the side for easy indexing and alignment. Designed to machine soft materials such as aluminum, plastic, zinc alloys. Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
Niagara Cutter N50162 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, Uncoated (Bright) Finish, Finishing Cut, 35 Degree Helix, 2 Flutes, 3″ Overall Length, 0.500″ Cutting Diameter, 0.500″ Shank Diameter
- Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Square nose end mills (also called square end) create sharp, unrounded cuts. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
Niagara Cutter N88652 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, TiCN Finish, Finishing Cut, 30 Degree Helix, 4 Flutes, 4.125″ Overall Length, 1.000″ Cutting Diameter, 0.750″ Shank Diameter
- Number of flutes varies fewer flutes have more chip-carrying capacity and more flutes produce a finer finish. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Square nose end mills (also called square end) create sharp, unrounded cuts. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating.
YG-1 E5065 Carbide Square Nose End Mill, Extra Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 6″ Overall Length, 0.25″ Cutting Diameter, 0.25″ Shank Diameter
- Four flutes produce a better finish than fewer flutes. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Suitable for general-purpose machining on hardened and high-alloy steel, steel casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic. Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills.
CGC Tools CEM764F4TICN Primate Square Nose End Mill, TiCN Coating, 4 Flute, 7/64″ Diameter, 3/8″ LOC, 1-1/2″ OAL
- This weapon of mass production destroy any competition. Extremely versatile in various materials, center cutting, solid sub-micron carbide. Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish. Usa, flat, 4 flute, 7/64″ diameter, 3/8″ length of cut, 1-1/2″ overall length, ticn coating.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
